Hot Rolled Mild Steel Plate Carbon Steel ASTM A516 Grade 70 Pressure Vessel Plates

Hot Rolled Mild Steel Plate Carbon Steel ASTM A516 Grade 70 Pressure Vessel Plates

ASTM A516 Grade 70 is an excellent choice for service in lower than ambient temperature applications, has excellent notch toughness and is used in both pressure vessels and industrial boilers.

A516 Grade 70 offers greater tensile and yield strength when compared to ASTM A516 Grade 65 and can operate in even lower temperature service.

Our plates come with mill certification in accordance with EN10204 3.1 or EN10204 3.2. Our plates are fully traceable, usually with hard stamping and we welcome any third party or customer inspection if required which can be arranged with the client.

 

Table 1: Chemical Composition of ASTM A516 Grade 70

Carbon (C) %
12.5mm or less
12.5 – 50mm
50 – 100mm
100 – 200mm
> 200mm
0.27
0.28
0.30
0.31
0.31
Manganese (Mn) %
12.5mm or less
• Heat Analysis :
• Product Analysis :

Over 12.5mm
• Heat Analysis :
• Product Analysis :

0.85-1.20
0.79-1.30

0.85-1.20
0.79-1.30

Phosphorus (P) %
(max) 0.035
Sulphur (S) %
(max) 0.035
Silicon (Si) %
• Heat Analysis :
• Product Analysis :
0.15-0.40
0.13-0.45

(Maximum values unless stated otherwise)

 

Table 2: Mechanical Properties of ASTM A516 Grade 70

Description Grade 65
Tensile strength (ksi) 70-90
Tensile strength (MPa) 485-620
Yield strength (ksi) 38
Yield strength (MPa) 260
Elongation in 200mm (min)(%) 17
Elongation in 50mm (min) (%) 21
Thickness (max)(mm) 205

(Minimum values unless stated otherwise)

 

(Please note: the technical information above is for guidance only – for exact specifications please check with our Sales Team)

Boiler Quality Steel Sheet A516 Pressure Vessel Steel

Boiler Quality Steel Sheet A516 Pressure Vessel Steel

We have listed the chemical and physical properties of the grades on the table below to allow for clear comparison. ASME SA 516 gr 70 has the highest tensile and yield strength of the three grades and this is due to the higher carbon content of the steel. The other principal alloying elements are the same as the other two ASME SA 516 grades.

 

Generally the higher the grade, in this case ASME SA 516 gr 70, the higher quality steel it is considered to be and the wider the range of possible applications. Our experience is that customers tend to choose either ASME SA 516 gr 60 or ASME SA 516 gr 70, with ASME SA 516 gr 65 being less popular. This is because the small difference between the grades mean that many heats of A516 70 can be dual or triple certified for all three grades and the small price differential means that for procurement purposes the additional cost of procuring ASME SA 516 gr 70 is small, whilst the engineering and logistical benefits can be significant.

 

ASME and ASTM Standards are harmonised so ASME SA 516 gr 70 is exactly the same as ASTM A 516 gr 70. On some specifications this is written as ASTM/ASME A/SA 516 gr70 or a similar combination of the same meaning.

 

A516 PRESSURE VESSEL STEEL CHEMICAL COMPOSITION

Steel Grade C Si Si (Min) Mn Mn (Min) P S
A516 60 0.23 0.45 0.13 1.3 0.79 0.035 0.035
A516 65 0.26 0.45 0.13 1.3 0.79 0.035 0.035
A516 70 0.28 0.45 0.13 1.3 0.79 0.035 0.035

 

ASTM A516 MECHANICAL PROPERTIES:

  A516 Grade 60 A 516 Grade 65 A516 Grade 70
Tensile Strength (ksi) 60-80 65-85 70-90
Tensile Strength (MPa) 415-550 450-585 485-620
Yield Strength (ksi) 32 35 38
Yield Strength (MPa) 220 240 260
Elongation in 200mm (%) 21 19 17
Elongation in 50mm (%) 25 23 21
Max Thickness (mm) 205 205 205

ASTM A516 Grade 70 / ASME SA516 Grade 70 Boiler Pressure Vessel Steel Plates

ASTM A516 Grade 70 / ASME SA516 Grade 70 Boiler Pressure Vessel Steel Plates

Gnee Steel supply high quality carbon steel plate for boiler and pressure vessel fabrication which is ideally suited to the high standards set by the oil, gas and petrochemical industry – this is why we stock an extensive range of carbon plates according to ASTM A516 Grade 70.

 

Equivalent Specifications and Standards of ASTM A516 Grade 70 / ASME SA516 Grade 70

Standard Description
ASTM/ASME A/SA516 – Grade 70
DIN Standard
British Standard BS1501-224-490A/B
European Norm EN10028 P355GH

 

Typical Chemical Composition of ASTM A516 Grade 70 / ASME SA516 Grade 70

Composition Percentage % Composition Percentage %
C 0.10/ 0.22 Cu 0.3
Si 0.6 Ni 0.3
Mn 1/ 1.7 Mo 0.08
P 0.03 Nb 0.01
S 0.03 Ti 0.03
Al 0.02 V 0.02
Cr 0.3

 

Typical Mechanical Values of ASTM A516 Grade 70 / ASME SA516 Grade 70

Properties Value
Tensile Strength (N/mm2) 510/ 650
Yield stress/ min (N/mm2) 335

Low Temperature Hot Rolled Mild Steel Plate Carbon Steel ASTM A516 Grade 70 Pressure Vessel Plates

Low Temperature Hot Rolled Mild Steel Plate Carbon Steel ASTM A516 Grade 70 Pressure Vessel Plates

We supply high quality carbon steel plate for boiler and pressure vessel fabrication which is ideally suited to the high standards set by the oil, gas and petrochemical industry – this is why we stock an extensive range of carbon plates according to ASTM A516 Grade 70 and ASME SA516 Grade 70.

The carbon steel plates come with mill certification in accordance with EN10204 3.1 or EN10204 3.2. Our plates are fully traceable, usually with hard stamping and we welcome any third party or customer inspection if required which can be arranged with the client.

Physical Properties Metric English Comments
Density  7.80 g/cc 0.282 lb/in³ Typical of ASTM Steel
Mechanical Properties Metric English Comments
Tensile Strength, Ultimate  485 – 620 MPa 70300 – 89900 psi
Tensile Strength, Yield  260 MPa 37700 psi
Elongation at Break  17 % 17 % in 200mm
21 % 21 % in 50mm
Modulus of Elasticity  200 GPa 29000 ksi Typical Carbon Steel
Bulk Modulus  160 GPa 23200 ksi Typical for Steel
Poissons Ratio  0.29 0.29 Typical Carbon Steel
Shear Modulus  80.0 GPa 11600 ksi Typical for Steel
Electrical Properties Metric English Comments
Electrical Resistivity  0.0000170 ohm-cm 0.0000170 ohm-cm Typical Carbon Steel
Thermal Properties Metric English Comments
CTE, linear  12.0 µm/m-°C 6.67 µin/in-°F Typical Carbon Steel
Specific Heat Capacity  0.470 J/g-°C 0.112 BTU/lb-°F Typical Carbon Steel
Thermal Conductivity  52.0 W/m-K 361 BTU-in/hr-ft²-°F Typical Carbon Steel
Component Elements Properties Metric English Comments
Carbon, C  0.31 % 0.31 % may vary with plate thickness
Iron, Fe  98.315 % 98.315 % as balance
Manganese, Mn  0.85 – 1.2 % 0.85 – 1.2 %
Phosphorous, P  0.035 % 0.035 %
Silicon, Si  0.15 – 0.40 % 0.15 – 0.40 %
Sulfur, S  0.040 % 0.040 %

 

A516 Gr.55-70 Hot Rolled Boiler and Pressure Vessel Steel Sheet for Sale

A516 Gr.55-70 Hot Rolled Boiler and Pressure Vessel Steel Sheet for Sale

A516 is a carbon steel plate grade utilized primarily in welded pressure vessels for moderate to lower temperature service. This material is produced in grades 55, 60, 65 and 70. This material is also offered in the normalized condition where improved notch toughness is required.

We have an extensive stock of ASME/ASTM A516 Boiler Plate. Our focus is in supplying very high quality plates for demanding applications in the oil and gas industry.

Chemical Composition

Steel Grade

C Si Si (Min) Mn Mn (Min) P S

A516 60

0.23 0.45 0.13 1.3 0.79 0.035 0.035

A516 65

0.26 0.45 0.13 1.3 0.79 0.035

0.035

A516 70 0.28 0.45 0.13 1.3 0.79 0.035

0.035

Mechanical Properties Gr 70:
Tensile:
70 to 90 ksi
Yield:
38 ksi min
Elongation:
17% min in 8” 21% min in 2”

Mechanical Properties Gr 65:
Tensile:
65 to 85 ksi
Yield:
35 ksi min
Elongation:
19% min in 8” 23% min in 2”

Mechanical Properties Gr 60:
Tensile:
60 to 80 ksi
Yield:
32 ksi min
Elongation:
21% min in 8” 25% min in 2”

Boiler and pressure vessel steel

ASTM A516-70 Plate As Rolled

ASTM A516-70 Plate As Rolled

ASTM A516 Grade 70 Plate is also called out as ASME SA516-70.  This steel plate grade is a medium carbon alloy that also contains amounts of manganese, phosphorus, sulfur, and silicon. A516 is primarily used for service in welded pressure vessels where improved notch toughness is required. It is typically found in moderate and lower temperature applications. A516 is sometimes called PVQ516.

Supplementary testing such as Charpy Impacts, Ultrasonic Examination and Carbon Equivalency are available. All plates over 1-1/2″ Thick are required to be normalized.  A516 is the most popular Pressure Vessel grade of steel plate in the industry. It is produced in grades 55, 60, 65 or 70.  The most common is Grade 70 or called out A516-70.

 

Chemical Composition

Grade C Mn P S Si
A516 Grade 70 0.27-0.31 0.79 – 1.30 0.035 max 0.035 max 0.13-0.45

 

Properties
Tensile Strength: 70-90 ksi
Yield Strength:    38 ksi

 

Typical Uses
A516-70 plate is a high strength, low alloy steel plate that offers an optimum combination of strength, weldability and notch toughness.

Applications include:
Bridges
Buildings
Automotiveand truck parts
Railroad cars
Cargo containers
Tote boxes
Construction equipment
Structural tubing
Lighting standards
Transmission poles

ASTM A516 Carbon Steel Plate

ASTM A516 Carbon Steel Plate

ASTM A516 Carbon Steel Plate

Steel Plate, carbon steel plate, hot rolled steel plate, cold rolled steel plate, stainless steel plates, steel circle, color coated steel plate, hot plate, steel coils, etc.
1)Used Area:
Ship building, Engineering construction, Mechanical manufacturing, Pavement slab, ect…
2)Size:
Width: 1500mm-4020mm
Length: 3000-18000mm
Thickness: 8-300mm
3)Material:
Carbon, Alloy, Stainless.
Q235, Q345, SS400, A36, S235JR, S355JR, S45C, S50C, A572, St37, St37-2, ST52, 304, 304L, 316, 316L, 321, 310S, etc.

4)Packing:
In container seaworthy packing…

5)Payment term:
T/T, L/C

components C
Si
Mn P
S
TAl
Nb V Ceq≤ Pcm
0.20 0.35 0.60-1.20 0.025 0.015 0.020 0.36 0.26
Use For the production of industrial and civil buildings such as brace and load-bearing beams, suitable for high-rise buildings and large span buildings
size 3000-118800mm*1500-4000mm*6-700mm
Thickness 6-700mm
Standard GB/T19879
Material Q390GJC
Packing According to the demand of the customer
Surface treatment Hot-rolled
Delivery time According to the quantity; asap, average period in 30 days.